GREENGUARD
HANEX product listing and certificate scope. Check the listed colour before specification.
Valid through 2026-10-09Open original document ↗DOCUMENT LIBRARY
Confidence in the details.
Find certificates, declarations and test reports by material. Review the product, test conditions and validity stated in each original document.
01 / ACRYLIC SOLID SURFACE
HANEX
Product certificates, material disclosures and technical documentation.
GREENGUARD Gold
Gold certification for the products identified in the accompanying listing.
Valid through 2026-10-09Open original document ↗HANEX HPD
Material content and health disclosure, published 16 November 2023. Review the scope and ingredient information in the source.
Valid through 2026-11-16Open original document ↗ISO 9001:2015
Current Hyundai L&C quality management certificate from the official headquarters library.
Valid through 2029-07-19Open original document ↗Product technical data sheet
Material composition, physical properties and test standards. Certification dates in this edition are historical; use the separate current certificates.
Open original document ↗ASTM E84 surface burning test
Complete 26 June 2024 report for HANEX N-WHITE. Results are limited to the tested sample and method.
Open original document ↗Official fabrication guidance
Open Hyundai L&C’s published fabrication document. Ask our India team for guidance on your design and material.
Open original document ↗HANEX Solid TVOC emissions
English report issued 29 April 2025 for the submitted HANEX Solid sample. Results apply to the stated sample and method.
Open original document ↗HANEX Solid RoHS test
English SGS report issued 9 April 2025 for the submitted HANEX Solid sample.
Open original document ↗HANEX Solid SVHC screening
English SGS report issued 9 April 2025 covering the listed candidate substances for the submitted HANEX Solid sample.
Open original document ↗Joint adhesive SDS · Component A
Safety data sheet revised 10 September 2024 for professional use of HANEX acrylic joint adhesive Component A.
Open original document ↗Joint adhesive SDS · Component B
Safety data sheet revised 10 September 2024 for professional use of HANEX acrylic joint adhesive Component B.
Open original document ↗Cascade physical properties
English report completed 25 April 2025 for the submitted Hanex Cascade sample.
Open original document ↗Stratum physical properties
English report completed 25 April 2025 for the submitted Hanex Stratum sample.
Open original document ↗Venato physical properties
English report completed 25 April 2025 for the submitted Hanex Venato sample.
Open original document ↗Multi-colour physical properties
English report completed 25 April 2025 for the submitted multi-colour HANEX sample.
Open original document ↗Galleria physical properties
English report completed 25 April 2025 for the submitted Hanex Galleria sample.
Open original document ↗02 / ARCHITECTURAL FINISHES
Interior Film
Seven BODAQ Interior Film laboratory reports, with previews and complete source PDFs.
These reports identify the submitted sample as BODAQ Interior Film. Results apply to the tested samples and conditions; they do not establish certification of a complete PHPL sheet or installed wall assembly.
FITI / Test report
Phthalate content
Seven tested phthalates each below 50 mg/kg (the quantification limit).
DEHP, DBP, BBP, DNOP, DINP, DIDP and DIBP. Below the quantification limit does not mean zero content.
KCL / Test report
Heavy metals
Lead, cadmium, mercury and hexavalent chromium: not detected at the stated detection limits.
Detection limits: Pb and Cd 5 mg/kg; Hg and Cr(VI) 2 mg/kg. Issued by Korea Conformity Laboratories (KCL).
FITI / Test report
Abrasion resistance
Mass loss: 20.0 mg after 1,000 abrasion cycles.
CS-10 abradant; 1,000 g applied weight. Tested after removal of the release liner.
FITI / Test report
Heat resistance
Measured cut gap: length 1.706 mm; width 0.083 mm.
Pre-treatment: 60 +/- 1 degrees C for 48 h, followed by conditioning. These measurements are not a maximum service-temperature rating.
FITI / Test report
Physical properties
Tensile: 48.6 / 45.1 N per 10 mm. Elongation: 212 / 226%.
Length / width results. Tear: 3.92 / 5.34 N. Adhesion: 8.76 N per 10 mm, at 180 degrees, with 5 min dwell.
FITI / Test report
Surface & stain resistance
17 of 19 listed agents: rating 5 (no visible changes).
Acetone and ethyl-butyl acetate: rating 1 (drastic changes). Keep these solvents away from the surface. Test subcontracted as noted in the report.
FITI / Test report
Gas toxicity test
Reported mean incapacitation times: 14 min 44 s and 13 min 14 s.
Tested film thickness: 0.4 mm; release liner removed. This report alone does not establish a fire rating for a finished PHPL sheet or wall assembly.
03 / DECORATIVE LAMINATES
PHPL
Collection information and documentation support for your specified laminate and application.
PHPL lookbook
The 22-page lookbook includes the pattern index and supporting BODAQ film test reports. Film reports should be read within their own scope.
Open lookbook ↗Product-specific documents
Ask our India team for documentation applicable to your PHPL sheet, substrate and intended installation.
Request PHPL documentation ↗Interior Film test library
Review the film component reports separately. These are not a whole-panel or complete assembly fire classification.
View film reports ↑